Marmitek MS9970 User Manual download pdf (Page 32)

32 MARMITEK

The security system does not operate:

Check that the POWER indicator on the SC2800

base station is on. If not, check that the PS500

power supply is plugged into a wall socket and

if the DIN connector is properly plugged into

the back of the base station.

Check that the mode switch on the base station

is in the RUN 1 or RUN 2 position.

Check that the system can be controlled via the

base station. If so, test the remote controls by

checking that the control indicator on the

remotes comes on when you press e.g. the

ARM button. Replace batteries in case

necessary and re-install the remote control.

When a zone indicator flashes slowly:

One of the door/window or motion sensors did

not send a signal to the base station for quite

some time. Check the batteries in the sensor. If

necessary, erase the zone (5.9) and re-install

the sensor (5.1).

When an error is detected during arming the

system, you’ll hear a dual tone “warning” signal.

When a sensor reports that there is a problem

(e.g. door or window open), you can choose to

not activate this sensor. You then have to press

the BYPASS button during the time that you

hear the dual tone signal. The press ARM again.

The zone indicator now is flashing rapidly. Once

the window is closed, the bypass will be

removed and the sensor will become part of

the system again.

When a zone indicator flashes rapidly:

You pressed the BYPASS button to arm the

system while a door/window or motion sensor

reported a problem. Correct the problem (close

door or window, replace batteries, etc.) to re-

activate this zone.

You hear a repeating dual tone signal while

you try to am the system and the system

does not go into arm mode:

Check the zone indicators on the base station.

When a door or window is left open, the zone

indicator for that zone will be on. When there’s

a problem with the sensor, the zone indicator

will flash slowly (press the ZONE 9-16 button

when you have installed more that 8 sensors

and you want to check the status of zones 9 to

16).

You now can do the following:

Key in your 4 digit PIN followed by DISARM.

Check all door- and window sensors for proper

operation (open and close e.g. a door but not

too fast, wait until the control indicator of the

sensor goes out). Check if all protected doors

and windows are properly closed. When

everything is OK, now arm the system again. As

long as you hear the dual tone signal, you can

press BYPASS to ignore the problem zone (the

zone indicator starts flashing rapidly). The arm

the system again. The problem zone will now

be ignored and is not protected!

You hear a repeating single tone to when

arming the system:

This is the normal way of operation for the

system. When arming the system, you have 1

minute to leave the premises because of the

arm delay. If required, you can switch off this

delay (refer to 5.6). After one minute the

repeating tone stops and the system is now

armed.

When you cannot switch on or off the lights

with the LIGHTS ON and LIGHTS OFF button

of your remote control:

Make sure that the House Code switch of the

lamp modules have been set to the same

House Code as the one under the cover of base

station (usually A). Make sure that the reference

address (for Home Automation functions) of the

base station is at the same Unit Code as the

one on the lamp module. Using the factory

default reference address A1 of the base

stations, the lamp module also has to be set to

A1.

Make sure that lights connected to the module

are switched on and the lamp(s) function

properly. Use another wall outlet. Check that

the control indicator on the remote control

comes on when you press the button. Replace

batteries in case necessary.

When using multiple phases in your house, it

may be required to couple these phases for

Marmitek X-10 signals. Contact your dealer or

for more information.

The alarm is activated while entering the

house before you can disarm the system:

Use the MAX position on the DS10

Door/Window Sensor. In that way you create a

delay between opening the door and causing

an alarm.

When you open a door or window and the

alarm is not activated:

Check that the security system is armed.

Check that the mode switch on the base station

is in the RUN 1 or RUN 2 position.

Check that pressing the TEST button on a door

or window sensor creates an alarm.

Check that the transmitter of a sensor is not on

or close to a large metal object. Position the

transmitter not on but next to metal frames

(e.g. on the wall) and observe metal supported

synthetic frames. Do not position the

transmitter close to armoured glass.

When an alarm is not initiated when pressing

the TEST button, check if the indicator on the

sensor comes on when pressing the button.

When the indicator does not come on, replace

the batteries.

9.TROUBLE SHOOTING

1 2 ... 27 28 29 30 31 32 33 34 35 36

Comments to this Manuals

No comments

Marmitek MS9970 User Manual Page 32

Comments to this Manuals

Related products and manuals for Security access control systems Marmitek MS9970