Marmitek MS9970 User Manual download pdf (Page 9)

3. CODE

By pressing this key, the sensor gets a new code (1

out of 65.536).

N.B.: When the sensor has been installed on the

system already, you have, after pressing the CODE

key, to erase the zone of this sensor on the base

station and re-install the sensor with its new code.

(refer to 5.9 and 5.1).

4. CONTROL INDICATOR

When you press the button TEST, or when the unit

is transmitting a signal to the base station, this

indicator will come on. When the indicator blinks

only weakly, the batteries have to be replaced.

5. BATTERY COMPARTMENT

INSTALLATION (install mode):

The motion sensor is activated by changes in

temperature. For that reason do not position the

sensor close to or above heaters or air conditioners.

The motion sensor has a range of 12m and an

opening angle of 90°. Due to the special lens, the

motion sensor it “looks down” into the area it has

to protect. Place the motion sensor always approx.

180cm above the floor and in such a way that the

sensor covers the area it has to protect well.

The supplied mounting bracket can be mounted

both in a 90° corner and on a flat surface. A

motion sensor works best when an intruder is

crossing the footprint of a sensor rather than

walking towards it.

Pressing the key for more than 3 seconds switches

the movement detector into “Walk Test mode”, in

which the detector merely lights up the diode

when it detects a movement and does not

transmit a radio signal. In this mode it is possible

to test the detection range of the sensor. When

the key is pressed again the detector returns to its

normal state.

The motion sensors operate according to the

Pulse Counting method. Depending on

temperature and settings, a possible motion will

only be reported to the base station after 30

seconds.

It may seem that the motion sensor is not

functioning properly, however, every motion

detected at any time always creates an alarm. The

advantage of this method is that the number of

false alarms is reduced dramatically.

6. MOUNTING THE ANTENNA OF EXTRA

MOTION SENSORS

Extra motion sensors are supplied with a wire

antenna and a separate antenna tube. For proper

operation, slide the plastic tube over the antenna

wire and push it firmly into the sensor housing.

PLACEMENT OF BATTERIES

Open the battery cover at the front of the motion

sensor. Place 4 AA batteries observing the polarity

instructions inside the battery compartment.

Close the battery cover.

ACTIVATING THE MS10

Push the TEST key on the back of the MS10 until

the indicator comes on

N.B.: When replacing the batteries of the MS10,

the unique code is maintained in the sensor. In

case the base station does not recognise the

MS10 after changing the batteries, you have to re-

install this sensor. You first have to erase this

specific zone (refer to 5.9) and re-install the

sensor (refer to 5.1).

9MS9470/MS9770/MS9970



4.4 MS10 MOTION SENSORS

CONTROLS

1. SENSITIVITY SWITCH

This switch allows you to set the sensitivity of the

motion sensor. This switch is particularly useful

when false alarms are easily created by heat

sources like radiators, etc. In position 1 the sensor

has the maximum sensitivity while in position 2

the sensitivity is reduced.

2. TEST

Used for activating and installing the sensor

during set-up of the system and can also be used

for testing the sensor.

door or window and the sensor will

instantaneously become part of the system again.

In case this does not work (e.g. the batteries have

been low for too long), you have to re-install this

sensor. You first have to erase this specific zone

(refer to 5.9) and re-install the sensor (refer to 5.1).

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 35 36

Comments to this Manuals

No comments

Marmitek MS9970 User Manual Page 9

Comments to this Manuals

Related products and manuals for Security access control systems Marmitek MS9970