Marmitek MS9970 User Manual download pdf (Page 8)

CONTROLS:

1. CONTROL

INDICATOR

When you press

the button TEST, or

when the unit is

transmitting a

signal to the base

station, this

indicator will come on. When the indicator blinks

only weakly, the batteries have to be replaced.

2. MIN/MAX

For setting a delay time of approx. 30 seconds.

When switched to the MAX position, the delay

time is activated. Position the DELAY switch

behind the cover to the MIN position

(instantaneous alarm). For an entrance door you

set the switch to MAX, allowing you to enter and

disarm the system When you want e.g. a garden

door to respond immediately, you switch the DS10

to the MIN position.

3. TEST

Used for activating and installing the sensor

during the installation procedure. Can also be

used to test the sensor.

4. MAGNETIC CONTACTS (NOT SHOWN)

The magnetic contacts are of the NC (Normally

Closed) type. The distance between magnet and

contact can not be more than 5mm. When

mounted, you have to make sure that the arrows

on magnet and contact line up. The length of

wire between contact and sensor can be

expanded or shortened. Make sure that the wires

are well connected and the screws tightened.

Multiple magnet switches can be placed in series.

5. BATTERY COMPARTMENT

Place 2 pieces AA batteries observing the polarity

instructions in the battery compartment. Use

preferably alkaline batteries.

INSTALLATION (install mode):

The Door/Window Sensor consists of a transmitter

and a magnetic contact. The magnetic contact

consists of 2 parts: the wired NC contact and a

separate magnet. Normally the magnet will make

the contact to close. When opening of a door or

window, the contact be opened and a message

will be sent to the base station (the red indicator

will come on).

The DS10 is primarily meant for doors and

windows, whereby the transmitter part and

contact will be placed on the frame and the

magnet on the moving part (door or window).

Look on door or window frame where the sensor

can be positioned without running the risk of

obstructing or damaging the sensor when

opening this door or window. Position the sensor,

if possible, as high up as possible. This will result in

the best possible range. Then mark the position of

the sensor and magnet contact. Do not place the

magnet contact directly on a metal surface. In

case of a metal or metal enforced plastic window-

frame, it is recommended to use a 5mm wooden

or plastic isolator between magnet contact and

frame.

For metal frames, the distance between contact

and magnet can not be more than 3mm when

door or window is in closed position. For wooden

frames this distance is 8mm, but in all cases the

opening should be kept to the minimum. To

mount the transmitter part, you remove the

batteries and screw the back of the transmitter

onto a suitable background.

For lift-up or sash windows, the contact and

magnet should NOT slide along each other, but

should be positioned in such a way that they

clearly move away from each other.

Remove the protective cover of the double-sided

tape on the magnet and position this on the

opening part of window or door. Remove the

protective cover of the double-sided tape on the

contact and position this on the frame.

N.B.: Make sure that the arrows on the contact

and magnet line up.

After testing the system, it is recommended to

also screw down the magnet on the surface.

6. MOUNTING THE ANTENNA OF EXTRA

DOOR/WINDOW SENSORS

Extra door/window sensors are supplied with a

wire antenna and a separate antenna tube. For

proper operation, slide the plastic tube over the

antenna wire and push it firmly into the sensor

housing.

ACTIVATING THE DS10

Push the TEST key of the DS10 for more than 1

second; the indicator blinks twice. Then press the

TEST key once more and close the battery cover.

N.B.: When replacing the batteries of the sensor

when the system is operational, you can make

sure that the sensor maintains its unique code

avoiding re-installation. To do this, you OPEN the

door or window that is protected by this sensor.

After replacing the batteries, you can close the

8 MARMITEK

4.3 DS10 DOOR/WINDOW SENSORS

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 35 36

Comments to this Manuals

No comments

Marmitek MS9970 User Manual Page 8

Comments to this Manuals

Related products and manuals for Security access control systems Marmitek MS9970